1
rogerpaul3 posted an answer for this Pool & Spa:
"This happens when the aqualink temp sensor fails. Replace the temp sensor."
rogerpaul3rogerpaul3 posted an answer for this Pool & Spa:
"Must replace the tank"
rogerpaul3rogerpaul3 posted an answer for this Raypak Pool & Spa:
"Check voltage to the gas valve and make sure it is getting 22-30 bolts when the gas valve..."
rogerpaul3rogerpaul3 posted an answer for this Pool & Spa:
"Clean pump basket out and make sure suction lines are not clogged. If all is clear check..."
rogerpaul3rogerpaul3 posted an answer for this Pool & Spa:
"Spaguts.com sells a shell repair kit that will work.you could also try an acrylic repair..."
rogerpaul3rogerpaul3 posted an answer for this Pool & Spa:
"Spaguts.com sells a shell repair kit that will work.you could also try an acrylic repair..."
rogerpaul3
rogerpaul3 posted an answer for this Zodiac Duo Clear System Chlorine Generator:
"Clean cell with 4:1 water:acid mixture to keep it from scaling up."
rogerpaul3rogerpaul3 posted an answer for this Zodiac Pool & Spa:
"The cell is dirty or it has failed. Clean with 4:1 water:acid mixture and then check the..."
rogerpaul3rogerpaul3 posted an answer for this Jandy Pool & Spa:
"I side the heat pump will be a small temp sensor mounted on the side of the inside area...."
rogerpaul3rogerpaul3 posted an answer for this Jandy Pool & Spa:
"The cell is bad or the cord is damaged. Look at the middle plate in the cell and you'll..."
rogerpaul3rogerpaul3 posted an answer for this Jandy Pool & Spa:
"It keeps the clock time.if the power goes out."
rogerpaul3rogerpaul3 posted an answer for this Jandy Pool & Spa:
"Make sure you have the correct version pda and antenna. The new 18 function white/black..."
rogerpaul3rogerpaul3 posted an answer for this Jandy Pool & Spa:
"Internal bypass rarely goes bad. More likely the high limit switches have corrosion on..."
rogerpaul3rogerpaul3 posted an answer for this Pool & Spa:
"Test wires with a volt meter. You if you have 110-125 volts between white and black then..."
rogerpaul3rogerpaul3 posted an answer for this Pentair Pool & Spa:
"Open the doors on the heater and look for signs of rodents. If it looks like rodents have..."
rogerpaul3rogerpaul3 posted an answer for this Pool & Spa:
"If the heater fires but shuts down after a few seconds then it's not recognizing flame and..."
rogerpaul3rogerpaul3 posted an answer for this Jacuzzi Pool & Spa:
"Impeller may be broken or clogged. Turn the pump off and remove the basket. Reach back..."
rogerpaul3rogerpaul3 posted an answer for this Pool & Spa:
"AGA is a symptom of a bigger problem. Its like check engine light for the heater. First..."
rogerpaul3rogerpaul3 posted an answer for this Pool & Spa:
"Ignore David, replace the backwash valve."
rogerpaul3rogerpaul3 posted an answer for this Pool & Spa:
"Replace it. They aren't really fixable."
rogerpaul3rogerpaul3 posted an answer for this Pool Pump Pool & Spa:
"C = common L = low H = high Green or green/yellow stripe always goes to ground. If..."
rogerpaul3rogerpaul3 posted an answer for this Pentair Pool & Spa:
"AFS stands for air flow switch meaning the heater doesn't know if the fan is working. If..."
rogerpaul3rogerpaul3 posted an answer for this Pentair Pool & Spa:
"It's a reversing cycle to help free it if stuck. It's normal."
rogerpaul3rogerpaul3 posted an answer for this Pentair Pool & Spa:
"eo1 error code indicates temp sensor failure. Replace temp sensor. If problem persists..."
rogerpaul3rogerpaul3 posted an answer for this Pool & Spa:
"Control board is likely shorted out and needs to be replaced."
rogerpaul3rogerpaul3 posted an answer for this Hayward Pool & Spa:
"The sensor is easy to replace with Phillips screw driver and adjustable wrench or wrench..."
rogerpaul3rogerpaul3 posted an answer for this Pool & Spa:
"Test phosphates and maintain below 500 PPB. Add additional chlorine if pool is being used..."
rogerpaul3rogerpaul3 posted an answer for this Pool & Spa:
"Test continuity between f1 and f2 on ignition control module when the fan is supposed to..."
rogerpaul3rogerpaul3 posted an answer for this Pool & Spa:
"Shaft seals leaking. Consult owners manual for shaft seal and replace."
rogerpaul3rogerpaul3 posted an answer for this Hayward Pool & Spa:
"The pump is not communicating with the control system. Check the comm wire and make sure..."
rogerpaul3rogerpaul3 posted an answer for this Hayward Pool & Spa:
"Check skimmers baskets and filter pump baskets to make sure there is no flow obstructions...."
rogerpaul3
Pool & Spa 48 answers
Sport & Outdoor - Others 8 answers
Computers & Internet 3 answers
Saws 1 answer
Irons 1 answer
Cell Phones 1 answer
