Sharp LC46LE835U TV - Page 3 - Answered Questions & Fixed issues
How do I stop the green light from flashing Sharp 46 aquos
Remove Main's plug press Input & Ch.Down button from LCD and put Main's plug to start LCD.
You will get K on Screen press Vol - & Ch- from LCD
You will get 1/10 page go to 9/10 by pressing ch.- button
You will get EEP off screen press ch- button from remote and press
Right side arrow from remote and press OK
On screen you will get EEP running.
After finish this oprestion remove plug and restart LCD.
11/28/2014 11:19:22 AM •
Sharp LC...
•
Answered
on Nov 28, 2014
•
109 views
How do I turn the TV speakers off on my Sharp LE 920UN television?
Look in the setup menu for the audio output option. On my menu system this is a sub menu under 'input terminal setting' for System Options. Change the 'Output Select' to 'Variable' which will disable speaker output and enable volume control of the audio out terminal on the back panel. If you have a receiver, you'll run all you audio through the receiver and can just turn the TV speakers off (variable) and forget about them....
11/27/2014 8:11:59 AM •
Sharp LC...
•
Answered
on Nov 27, 2014
•
186 views
How do I do a Reset of my Sharp Aquos LC70LE847U?
These blinks [flashes] are fault indication (Error Codes). From the number of blinks occur at one time switch ON, you can get an idea about the faulty circuit section inside it. This will make repair easy. These are called blinking codes. Make sure about the exact number of blinking of the standby/power LED, by switching On & OFF the set, for at least two times. Count it carefully. If you wish to get some details, check the site linked here. It has details about blinking codes, and fault locating procedure, to many popular brand TVs and other devices.
http://electronicshelponline.blogspot.com/
Blinking codes details to many popular brand TVs are given. Surf the site with patience.
To make it a hard reset, just unplug the TV from AC mains wall socket, and re-plug it back after 15 minutes or so. This procedure will make it a hard reset. If you want to make it a system reset [Factory Reset]; you have to enter its service mode option, and select the factory reset option. If you wish to get some details; check the site linked above. Pull up older posts. Surf the site with patience.
Service mode entry, adjust and exit procedure to many popular brand TVs are given. Never forget to exit the service mode, after all adjustments have been done.
9/14/2014 3:50:01 PM •
Sharp LC...
•
Answered
on Sep 14, 2014
•
1,226 views
Very blurry picture / vertical colour lines
It sounds that the LVDS cable; the cable that connects to T'Con board to LCD panel is loosely fitted. Check it first. If it is found OK, the panel itself should be suspected. If you wish to get more details,
http://electronicshelponline.blogspot.com/ Pull up older posts there, either by its left side bar, or
see it in Timslide option. Faulty screenshots of LCD TV screens, have been illustrated. Compare them to your TVs present screen view, and be sure. Check the site with patience.
6/26/2013 8:27:06 PM •
Sharp LC...
•
Answered
on Jun 26, 2013
•
441 views
LC-19sb27UT
Check its sound settings. Check whether 'mute' function is on. If all the setting are ok, check its speaker. If speaker too is ok, check and replace damaged component/s at the audio output section circuit. If you wish to get some service help,
check this link.
3/9/2013 10:40:41 AM •
Sharp LC...
•
Answered
on Mar 09, 2013
•
55 views
Sharp aqous picture error
You Vertical Problem can you go to advance settings to adjustvertical Size? Or center the picture
11/2/2012 5:32:23 AM •
Sharp LC...
•
Answered
on Nov 02, 2012
•
158 views
Sharp Lc-26sb24u white screen with sound
You will get a white screen when you unplug the t-con from the main board. Doing so removes power to the LCD panel. Verify that all of your voltages from the power supply are correct. If they are, I'd look at the t-con board. It sounds like there is a problem with the t-con that is pulling down the main board.
5/11/2012 5:41:14 AM •
Sharp LC...
•
Answered
on May 11, 2012
•
1,783 views
Sharp lc 60e88un shutdown the 24v from power board no 12v
to check for led eror vol_ channel+ hold and press power switch once andrelease only power switch triangle light should come on then release the vol and channel knobs if set comes on the leds defective in screen
3/2/2012 8:24:38 PM •
Sharp LC...
•
Answered
on Mar 02, 2012
•
197 views
Not finding what you are looking for?
